Shenzhen Xin Yuan Electronic Technology Co., Ltd.
购物车图片 购物车 ( )
找服务 找新闻
服务热线: (86)13928411439

VL53L0X Temps-de-Vol (ToF) Laser Allant Capteur Breakout 940nm GY-VL53L0XV2 Laser Distance Module I2C IIC

上市日期: 2017-08-31
建议销售价: 0

The ST Microelectronics VL53L0X is a flight time ranging system integrated in a compact module. The board is the carrier of the VL53L0X, so we recommend that you read the VL53L0X data sheet (1MB PDF) carefully before using this product.

VL53L0 using ST FlightSense technology of infrared laser precise measurement of emitted pulses at the small distance between the object and the detector is reflected back to the required time, so it can be regarded as a small, self-contained laser radar system. This time-of-flight (TOF) measurement allows it to precisely determine the absolute distance to the target, whereas the reflectivity of the object does not greatly affect measurement. The sensor can report up to 2 m (6.6 ft) distance resolution is 1 mm, but its effective range and accuracy (noise) is heavily dependent on the environmental conditions and target characteristics (such as reflectivity and size) and sensor configuration. (the accuracy of the sensor is specified to be excellent, from + 3% to range = + 10%).
The measurement range is provided by the I2C (TWI) interface of the sensor, which is also used to configure the sensor settings, and the sensor also provides two additional pins: turn off input and interrupt output.
VL53L0X is a great IC, but it's small, leadless, LGA package that makes it difficult for typical students or hobbyists to use. It also works at the recommended voltage of 2.8 V, which may make it difficult to interface at 3.3 V or 5 V microcontroller. From our board to solve these problems, making it easier to start using the sensor, while maintaining the overall size as small as possible.
PIN description
VDD regulated 2.8 V output. Almost 150 mA can be used to power external components. (to bypass the internal voltage regulator, you can use this pin as the 2.8 V input and disconnect the VIN).
VIN this is the main 2.6 V to 5.5 V power connection. The SCL and SDA level shifters raise the I2C line to this level.
GND power ground (0 V) connection. Your I2C control source must also share a common ground with the board.
SDA level conversion I2C data line: HIGH is VIN, LOW is 0 V
SCL level shift I2C clock line: HIGH is VIN, LOW is 0 V
XSHUT this pin is a low active shutdown input; by default, the board pulls it up to VDD to enable the sensor. The pin is driven low to allow the sensor to enter the hardware standby state. This input does not perform level conversion.
Package includes:

1X GY-VL53L0XV2V L53L0X sensor distance flight time 

VL53L0X Temps-de-Vol (ToF) Laser Allant Capteur Breakout 940nm GY-VL53L0XV2 Laser Distance Module I2C IIC

VL53L0X Temps-de-Vol (ToF) Laser Allant Capteur Breakout 940nm GY-VL53L0XV2 Laser Distance Module I2C IIC

Hot Products / Hot products More
2019 - 01 - 31
TTGO T-Camera ESP32 WROVER & PSRAM Camera Module OV2640 Camera Module 0.96 OLED  T-Camera pictureT-Camera specification   Master Chip: esp32 dual-core Protocol: Wi-Fi 802.11 b/g/n & Bluetooth 4.2 BLE & BR/EDR Flash: 4MBytes  PSRAM: 8MBytes  Display chip: SSD1306 ...
2018 - 11 - 13
TTGO T-Journal ESP32 Camera Module Development Board OV2640 Camera  SMA Wifi 3dbi Antenna 0.91 OLED  Camera BoardHardware SpecificationsChipset ESPRESSIF-ESP32-PCIO-D4 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessorFLASH QSPI flash/SRAM, up to 4 x 16 MBSRAM 520 kB SRAMKEY reset,IO32dispaly 0.91 SSD1306Power indicator lamp redUSB to TTL C...
2017 - 10 - 16
describeTTGO ForArduino UNO LoRa v1.0 is a for Arduino development board with Lora chip. The development board MCU uses atmega328P, and the communication module adopts the Lora module of Anxin, which can realize the function of for Arduino and Lora wireless communication.   For more details, please see the link: Invoice list:UNO LoRa MEGA328 ...
2017 - 10 - 17
describe:The 433MHz antenna must be used in conjunction with the IPEX interface (if the antenna is not connected, it may damage the LoRa chip)Lithium battery charging and discharging circuit, when the battery is full, the blue LED will stop working. When using, pay attention to the positive and negative of the battery, otherwise it will be damaged!Using the IO port touch screen touch signal input,...
  • 资质认证


  • 支付安全


  • 专人服务


  • 售后无忧


The unified hotline:

  • Ali Express

  • ebay

  • "Sweeping" attention to us, more activities, surprise waiting for you
    E-mail:       Wechat: 13928411439       QQ :3004603945       Facebook: lily go
    Copyright ©2005 - 2013 Shenzhen Xin Yuan Electronic Technology Co., Ltd.